ABOUT THE 12″ STD
12-inch Standard Steel Pipe Bollards can be used for Heavyweight Entry Barricades. At close to 300 lbs for an 6-footer, they must be set into place carefully with mechanical aids to avoid injury. The concrete footings are substantial, and the pipe itself holds a lot of concrete, all making these what we consider, Heavyweight Bollards.
GENERAL APPLICATIONS: The 12″ STD Pipe might be used to protect:
- Building entrances from errant vehicles and ram-raids. See Bollard Barriers for Store Front Protection.
AS A BARRICADE: A pier footing of 30″-36″ deep is likely sufficient in an installation of 12″ STD Steel Pipe Bollards. The hole may be excavated or augered with a 36″ auger. This is a seriously substantial barrier to all sized vehicles and even trucks. Reinforcing the concrete with rebar, rebar embedding inside concrete filled bollard as well as trench installation of an array of bollards are all ways to further fortify a bollard system against higher speed vehicle impacts. By tying together 12″ Standard pipes with a reinforced concrete trench, you are creating a multi-ton system with unrated, yet undeniably great stopping capability. But, for more certainty in the barrier’s stopping capability in a more compact form, it is advised to use an impact-rated bollard system such as the K4 or K12. Also, see Bollard Barriers for Store Front Protection.
VARIETIES: ASTM A500 Carbon Steel Pipe is the common go-to choice for bollards. Although, it is sometimes sufficient to use a structural grade untested pipe. Of course, we also offer pipe that meets various prescribed ASTM and ASME standards. See “Pipe Varieties” below.
Name: 12″ STD Steel Pipe
Nominal Size: 12″
Wall Thickness: 0.375″
Inner Diameter (ID): 12.0″
Outer Diameter (OD): 12.75″
Circumference: 40.06″ (approx 40 1/16″)
Weight: 49.61 lbs/ft
Default Grade: ASTM A500 Grade A
Finishes: Bare Steel, Primed, Galvanized
Primer Colors: Red Oxide, Yellow & Gray
BOLLARD INSTALLATION SPECS
Minimum Pier Footing Diameter: 36″
Auger Size: 36″
Install Depth: 30″ may be sufficient
Install Height: 30″-36″ Typical
Bollard Pipe Lengths Available: 5′, 5.5′,6′,6.5′, 7′ and more
6′ Weight: 297.66 lbs
7′ Weight: 347.27 lbs
8′ Weight: 396.88 lbs
Concrete: Volume for 36″ Diameter, 36″ Deep Footing + Pipe Fill is 0.88 Yards
System Weight: 36″ Dia. x 36″ deep concrete pier and 6′ bollard is approx. 3820 lbs
PIPE SIZES EXPLAINED
Confused about "Schedule" or "Standard" wall thicknesses? See this short article.
This Pipe may be available in the following types and grades:
Electric resistance weld (ERW), seamless (SMLS), and double submerged arc weld (DSAW) in all published schedules and walls, Grades ASTM A-500 GR A & GR B, ASTM A-53 GR B, ASME SA-53 GR B, ASTM A-106 GR B, ASME SA-106 GR B, AP1 5L X-GRADES, ASTM A-252 GR 1, 2, AND 3, ASTM A-139 GR B, and ASTM A-501.
UNTESTED PIPE VARIANT
This pipe may also be available as untested pipe without an ASTM rating. It is then referred to by Diameter and Wall Thickness only; no Schedule #, Standard, XH or XXH etc. Untested pipe can be much cheaper, and is often perfectly fine for bollard applications since the testing is really about pressure testing; how much PSI the pipe can withstand when filled with a pressurized liquid or gas. Bollards are just filled with concrete, so PSI ratings are generally not applicable. Their may be a small or negligable weakness in terms of bollard strength associated with untested pipe.
MORE PIPE SIZES AND THICKNESSES
See bottom of page for all of our pipe sizes and wall thicknesses. We offer 1/8" to 36" Diameters and walls from SCH 5 to SCH 160 XH Extra Heavy and XXH Double Extra Heavy.
COST OF 12-inch Standard STEEL PIPE BOLLARDS
Please Request a Quote below. Price can change daily and depends upon quantity and delivery location.
We find the best total pipe and freight price based on your delivery location. Our pipe is freighted out of Minnesota, Illinois, Michigan, New Jersey, & Texas.
NEW ARTICLE -> HOW TO INSTALL IN-GROUND BOLLARDS
Read our thorough guide on How To Install In-Ground Bollards. Complete with pictures, links and lists of materials, equipment and tools, these step-by-step instructions will help anyone installing bollards.
GET A QUOTE ON BOLLARD PIPES
Answer some questions below on our Bollard Pipe Quote Request Form and you'll get a quote back from us the same or next day. The shipping destination helps us give you the BEST QUOTE by calculating the freight cost.
There's no risk in getting a quote. We don't do mass emailings and we don't share your info with anyone.
WANT AN INSTALLATION QUOTE TOO?
We install bollards locally, and remotely when the job is right. In the winter we are slow in Minnesota, so consider our reduced installation winter rates if you are in a warmer climate.
All Pipe Sizes Available
Below we have a chart of pipe sizes that are available for quote.